All Posts
Equipment & Maintenance

How to Winterize a Car Wash Before the First Freeze

How to winterize a car wash: test weep systems and heat, service doors, clear drains and switch chemistry before the first freeze, by wash format.
Summarize
“How to winterize a car wash” next to a WashUp Services card for a yearly glycol and floor heat check, with a reminder alert

How to winterize a car wash comes down to one rule: protect everything that holds water before the first overnight freeze. In practice, that means you test the weep system and the heat, service the doors, clear the drains, and switch to winter chemistry. Winter is when salt brings cars in. In Q1 2025, Rinsed linked more snowfall days to more road salt and higher demand for retail washes (Rinsed industry data via ICA).

That’s the catch. The weeks that pay for the year are the same weeks a frozen weep line or an iced-up door can shut you down, and the first sunny Saturday after a storm is the worst day to find out.

Key takeaways

  • Rinsed’s Q1 2025 data tied more snowfall to more road salt and more retail washes, members washed more often than a year earlier, and same-store sales rose 12.4% year over year (Rinsed industry data via ICA, May 2025).
  • Across more than 7,400 U.S. tunnel sites, heavier snowfall went with a higher share of premium plan purchases in AMP’s Q3 2025 data (AMP data via CarwashPro, November 2025).
  • One wash owner puts the weep system’s safe zone at 38 to 40 degrees, and the sensors and solenoid valves should be tested every fall by disconnecting the power (Professional Carwashing & Detailing).
  • Most weep systems use a normally open solenoid valve, which lets water flow when the coil has no power, and a sensor on the outside wall of a heated room can read 5 to 10 degrees high (Kleen-Rite vendor guidance).

When should you winterize a car wash?

You should winterize a car wash before the first overnight freeze, not after it. Test every heater, door and weep system while it’s still mild, so repairs are finished and parts are on the shelf before the coldest days, per William Stokes of Ultimate Supplies (Professional Carwashing & Detailing).

Warm-weather markets aren’t off the hook. Even in a warmer climate, one freak winter storm can freeze a wash solid (Professional Carwashing & Detailing).

Put a number on what’s at stake before you decide the walk-through can wait. A tunnel washing 55 cars an hour at a $15 average ticket gives up about $825 in wash revenue for every hour it’s closed (WashUp calculation; use your own car count and ticket). The repair bill comes on top of that, which is why we wrote up the real cost of equipment downtime separately.

What freezes first at a car wash?

Water that sits still freezes first. At a self-serve, that’s the wands and foam brush hoses hanging full all night. At a tunnel or an in-bay automatic, it’s the supply lines, the nozzles and anything near a door that opens to the wind.

What freezes first at a car wash, by format
AreaWhat freezesWhat prevents it
Self-serve baysWhat freezesWands, foam brush hoses and the lines that feed themWhat prevents itA weep system on a thermostat, plus anti-freeze soap for the foam brushes
In-bay automaticWhat freezesSupply hoses and the nozzles on the machine, bay doorsWhat prevents itWeep water through the nozzles, bay and floor heat, a door closed during the cycle
Express tunnelWhat freezesOverhead supply lines, doors and their tracks, standing waterWhat prevents itInfrared heat over the equipment, door seals, heat trace or radiant tubing in the troughs
BackroomWhat freezesWater heaters, the floor heat loop, pump and chemical linesWhat prevents itGlycol checked, the system pressure tested, equipment room heat tested before winter
Lot and walkwaysWhat freezesOverspray at bay entries and exitsWhat prevents itSalt where people walk; a colored halide salt shows where it’s been spread

Sources for the table: weep systems, anti-freeze soap, heat and salt from Professional Carwashing & Detailing; doors from Josh Hart of Airlift Doors in PC&D; the backroom loop from Chris Rojas of Carwash Boilers Inc. in PC&D.

How do I winterize an express tunnel car wash?

To winterize an express tunnel, test the heat before the first freeze, service the doors and their seals, get the conveyor and cloth ready for the busy season, check the backroom heating loop and pumps, and confirm the undercarriage applicators spray clean. Then show the crew what a freezing morning looks like, because the opener is who catches a frozen line first.

  1. Heat the tunnel and test it. Infrared gas tube heaters above the equipment can run overnight, so the equipment itself soaks up heat (PC&D). Lines in overhead troughs get electric heat trace or hydronic radiant tubing.
  2. Service the doors. Josh Hart of Airlift Doors recommends oiling the air operators and greasing the bearings and hinges before the cold sets in. Replace any torn weather seals while you’re at it. If a door freezes to the floor, start with a new bottom seal, then add a plastic threshold so water stops pooling under it (PC&D).
  3. Get the conveyor ready for volume. Robert Andre, president of CarWash College, says to check the chain and rollers, replace anything that won’t last the season, check the drive sprocket and the take-up for wear and alignment, and clean out the pit before the season starts (PC&D).
  4. Fix the cloth and the bearings. Replace missing or damaged cloth and aim for 3 to 4 inches of cloth on the vehicle. Grease each bearing with 2 to 3 pumps, and don’t over-grease (Andre, PC&D).
  5. Check the backroom loop. Chris Rojas of Carwash Boilers Inc. lists inspecting water heaters and boilers, checking glycol and changing it if needed, pressure testing the system, and checking the deicing system’s set points (PC&D). While you’re back there, confirm the high-pressure pumps run at the right pressure and the air compressor filters are clean.
  6. Watch the undercarriage applicators. During the ghost wash (a full cycle with no car in the tunnel), watch the underbody wash and protectant applicators. Dan Kramer of Stone Soap Co. says to brush them clean daily and replace underbody nozzles every year. Clear a clog with compressed air, not a metal tool, which damages the nozzle (PC&D).

Good to know: after a power outage, some doors open on their own when the power comes back. Hart recommends a floor cut-off tied to the photo eyes and the opener, confirmed with your door provider, so a tunnel doesn’t sit wide open on a frozen night (PC&D).

How do you winterize an in-bay automatic?

Winterizing an in-bay automatic means keeping the bay warm and closed, and keeping water moving through the lines that feed the machine. An in-bay automatic (IBA) is a single bay where the machine moves around a parked car, so the whole wash lives in one room you can heat.

  • Test the heat first. Before winter, check the thermostats and fans in the equipment room and on the automatic, and check the floor heat system’s pressure, adding anti-freeze if it needs it (PC&D).
  • Keep a door closed during the cycle. Hart’s advice is to close at least one door while the wash runs, so wind doesn’t blow chemistry back out of the bay (PC&D).
  • Weep the nozzles. A weep system doesn’t just serve self-serve wands. It also streams water through the miscellaneous nozzles on IBA equipment (PC&D).
  • Add a desalting pass. Kleen-Rite’s staff suggest swapping the bug remover for a desalting product, which can double as a low-pH pass on touchless washes (PC&D).

How do you winterize a self-serve car wash?

A self-serve car wash winterizes around its weep system, because the wands and foam brushes sit full of water all night with nobody on site. Kleen-Rite’s staff call the weep system the most important piece of winter equipment for most self-serve operators (Professional Carwashing & Detailing).

  • Set the weep temperature. Most systems run on a thermostat. Dave Edwards, owner of The CAR WASH on Hamlin Hwy. and The CAR WASH on Rt. 6, puts the safe zone at 38 to 40 degrees (PC&D).
  • Place the sensor where it reads true. Keep it out of direct sunlight and off the outside wall of a heated room, which can make it read 5 to 10 degrees high (Kleen-Rite vendor guidance).
  • Know which way the solenoid fails. Most weep systems use a normally open solenoid valve, which lets water flow when the coil has no power (Kleen-Rite vendor guidance). If yours is normally closed, an outage on a cold night stops the weep exactly when you need it.
  • Test it every fall. Check the sensors and solenoid valves, then test the system by disconnecting the power source (PC&D).
  • Heat the floor and the troughs. Heat self-serve bays with hydronic radiant heat built into the slab, and put heat trace or radiant tubing on the lines in overhead troughs (PC&D).

The chemistry changes too. Here’s what to swap before the first cold snap.

Winter chemistry and settings to change
WhatSwitch toWhy
Foam brush soapSwitch toA methanol-based anti-freeze soapWhyUses less water than weeping the brush and keeps weep water off the floor; it costs more per car
Hydrominder metering tipSwitch toA different tip as temperatures dropWhyKeeps the anti-freeze mix right for colder nights
Bug removerSwitch toA desalting productWhyRemoves salt, and doubles as a low-pH pass on touchless and tunnel washes
Vacuum and detail chemicalsSwitch toWinter formulasWhyWinter shampoo, spot remover and carpet protectant work to about 5°F
FragranceSwitch toOil-based fragranceWhyWorks to about 0°F
Undercarriage passSwitch toSalt-removing chemistry plus a rust inhibitor or protectantWhyTakes off salt and brine and leaves a protective layer on the underbody

Source for the table: Kleen-Rite’s staff and the undercarriage experts quoted in Professional Carwashing & Detailing and PC&D.

What should your crew check on a freezing morning?

On a freezing morning, the opener should confirm the heat and the weep are running, walk every bay exit for ice, salt where people walk, and run a ghost wash while watching the undercarriage applicators before the first car. Dress for it, too: three loose layers, insulated waterproof boots and a high-visibility vest anywhere near moving cars, per the cold-weather guidance in PC&D.

  • Heaters on and holding temperature in the tunnel or bays and the equipment room
  • Weep water running at every wand and foam brush
  • Doors opening and closing without dragging on ice
  • No ice at the bay exits or in front of the pay station
  • Undercarriage applicators spraying a full pattern during the ghost wash

In WashUp, keep this as a situational list named something like “Hard freeze.” It sits ready in the Task Library until someone on shift pulls it into the day from Tasks, then One-Time, then Use situational list (Create a situational task list). The help center’s analogy fits: it’s shoveling the driveway after a snowstorm. For the backroom, our free drainage and plumbing inspection template covers the drains and lines that freeze first.

Where WashUp fits

Winter prep fails the same way every year: somebody knew the weep sensor needed testing, and it lived in their head. In WashUp, each fall check becomes a service on the equipment it belongs to, like the Water Heater / Boiler, set to repeat Yearly with a reminder up to 30 days before it’s due (Services). Add a temperature reading in °F to your backroom inspection, and a reading outside the thresholds you set rates itself Red (Critical) or Yellow (Needs Attention) and opens an Attention Item when the inspection is saved (Numeric inspection items). Breakdowns are expensive—and preventable.

Get your fall checks out of somebody’s head. Book a demo, or try WashUp free for 14 days (pricing).

Frequently Asked Questions

At what temperature should a car wash weep system turn on?
How often should you test a car wash weep system?
What car wash chemicals should change for winter?
Do car washes get busier in winter?

Sources & Author

Written by
Jackson Bitton, co-owner and CIO of WashUp
Jackson Bitton
Co-owner and CIO, WashUp
Read time
9
min read
Published on
November 18, 2026
Last updated
November 18, 2026
Ready to see what your wash could look like with WashUp?